AN Series

Parts Identification Chart, AN Series, BN Series, ANL Series, Catalog Download

 

						DIAMETRAL2 CLEARANCE		RADIAL CAPACITY (lbs)	TORQUE CAPACITY @G13 (in-lbs)	TYPICAL BORE FOR TORQUE			TYPICAL BORE FOR BEARING MOUNT
d nominal	d (in)	w2 (in)	PART NUMBER	d min (in)	D max (in)	G1 (in)	G2 (in)			TC (in-lbs)	D min (in)	D max (in)	D min (in)	D max (in)
4 mm	0.157	0.236	AN4X8C	0.156	0.195	0.032	0.039	20	3	2	0.190	0.192	0.193	0.195
3/16	0.188	0.250	AN018025C	0.187	0.226	0.032	0.039	23	4	3	0.219	0.221	0.224	0.226
6 mm	0.236	0.236	AN6X6C	0.235	0.274	0.032	0.039	30	6	4	0.269	0.270	0.273	0.274
1/4	0.250	0.250	AN025025C	0.249	0.289	0.032	0.039	45	9	4	0.283	0.285	0.287	0.289
5/16	0.313	0.250	AN031025C	0.312	0.370	0.048	0.058	65	11	7	0.362	0.364	0.368	0.370
3/8	0.375	0.250	AN037025S	0.374	0.433	0.048	0.058	190	21	15	0.424	0.426	0.430	0.433
7/16	0.438	0.250	AN043025S	0.437	0.495	0.048	0.058	230	25	18	0.487	0.489	0.492	0.495
1/2	0.500	0.250	AN050025S	0.498	0.558	0.048	0.058	270	50	25	0.549	0.552	0.555	0.558
1/2	0.500	0.750	AN050075S	0.498	0.558	0.048	0.058	810	150	75	0.549	0.552	0.555	0.558
5/8	0.625	0.250	AN062025S	0.623	0.683	0.048	0.058	320	75	37	0.674	0.677	0.680	0.683
16 mm	0.630	0.197	AN16X5S	0.628	0.688	0.048	0.058	250	58	30	0.678	0.682	0.685	0.688
11/16	0.688	0.250	AN068025S	0.686	0.746	0.048	0.058	370	100	50	0.737	0.740	0.743	0.746
19 mm	0.748	0.236	AN19X6S	0.746	0.826	0.066	0.078	420	98	60	0.814	0.817	0.823	0.826
3/4	0.750	0.250	AN075025S	0.748	0.828	0.066	0.078	440	115	70	0.816	0.819	0.825	0.828
22 mm	0.866	0.276	AN22X7S	0.864	0.944	0.066	0.078	550	220	135	0.932	0.935	0.941	0.944
7/8	0.875	0.500	AN087050S	0.873	0.953	0.066	0.078	1200	325	200	0.941	0.944	0.950	0.953
1	1.000	0.500	AN100050S	0.998	1.078	0.066	0.078	1300	425	260	1.066	1.069	1.075	1.078
28 mm	1.102	0.472	AN28X12S	1.100	1.181	0.066	0.078	1330	525	325	1.168	1.171	1.177	1.181
1—1/8	1.125	0.500	AN112050S	1.123	1.203	0.066	0.078	1440	530	330	1.188	1.192	1.199	1.203
30 mm	1.181	0.355	AN30X9S	1.179	1.259	0.066	0.078	980	440	390	1.247	1.250	1.256	1.259
1—1/4	1.250	0.500	AN125050S	1.248	1.328	0.066	0.078	890	530	410	1.316	1.320	1.324	1.328
1—3/8	1.375	0.750	AN137075S	1.373	1.453	0.066	0.078	1500	900	500	1.441	1.442	1.449	1.453
35 mm	1.378	0.433	AN35X11S	1.376	1.456	0.066	0.078	820	550	290	1.444	1.448	1.452	1.456
1—1/2	1.500	0.500	AN150050S	1.498	1.578	0.066	0.078	1100	795	420	1.566	1.570	1.574	1.578
1—9/16	1.563	0.500	AN156050S	1.561	1.641	0.066	0.078	1100	860	460	1.629	1.633	1.637	1.641
40 mm	1.575	0.472	AN40X12S	1.573	1.653	0.066	0.078	1000	835	445	1.641	1.645	1.649	1.653
1—5/8	1.625	0.500	AN162050S	1.623	1.703	0.066	0.078	1200	940	500	1.691	1.695	1.699	1.703
42 mm	1.654	0.512	AN42X13S	1.652	1.731	0.066	0.078	1200	890	475	1.720	1.724	1.727	1.731
1—3/4	1.750	0.500	AN175050S	1.748	1.828	0.066	0.078	1200	1110	590	1.816	1.820	1.824	1.828
47 mm	1.850	0.551	AN47X14S	1.848	1.928	0.066	0.078	1400	1360	720	1.916	1.920	1.924	1.928
2	2.000	0.500	AN200050S	1.998	2.097	0.080	0.098	1100	1175	675	2.082	2.087	2.092	2.097

1. See SIZE RANGE OF STANDARD RINGS chart here for other widths which are available. Radial load and torque capacities are generally proportional to width. Performance is influenced by design of mating components and assembly procedures - actual capacities may vary from the stated values. For sizes or load requirements other than shown, contact our Engineering Department for recommendations.

2. Diametral clearance or Diametral Gap is the void where the Tolerance Ring fits (mathematically represented by D-d) The size of this gap determines the amount of interference fit. G1 and G2 are design limits.

3. Torque capacity is dependent on fit. Torque Capacity @ G1 is the expected torque capacity at the tightest fit allowable. TC is the expected minimum torque transfer capacity at the Typical Bore For Torque diameter range (which occurs with Dmax).

 

USA TOLERANCE RINGS
85 Route 31 North, Pennington, New Jersey 08534
phone:609-745-5000; fax:609-745-5012